Bug Reports - Automobilista 2 (Read the Opening Post)

Not a bug, but incorrect liveries on the Nissan GT1s.

I see that the nose is very yellow in two cars out of three in AMS2. But isn't it so that the nose is yellow because it was covered with protective film and that film has yellowed over 25 years and it actually was originally almost clear see through!? The liveries seem to be accurate as of now in the museum, but not as of the time they raced, which is a shame.

I really wish this is fixed so we can race the cars as they raced back in the day.












Someone also pointed out that the 1997 and 1998 cars noses are slightly different:

 

Formula Inter: Raindrops run the wrong way (down) on the windshield.
No engine noise in non-trackside replays

Absolute magic car otherwise!

 

Trueforce has no effect.
Using Logitech DD pro in 923 cimpatibility mode. Tried in DD mode. No trueforce effects felt anywhere.

Logitech has AMS2 listed as having Trueforce support. Is this not true?

 

Continuing this, I realized what's going on: tyres get warmers for the race, raising up the pressure you selected. Which is not there in either practice nor qualy.

 

Version: 1.4.6.1.
Track & Layout Used: Spielberg
Car Used: F Inter
Applicable Settings: Single event
Report: Between Niki Lauda Kurve and short cut AI goes off the track without reason

 

Version: 1.4.6.1.
Track & Layout Used: Spielberg
Car Used: F Inter
Applicable Settings: Single event
Report: Cool down lap entering pitlane AI is still a bit reckless

 

Porsche 911 RSR 74:

Also no drivers in car when using custom liveries!

 

Version: 1.4.6.1.
Track & Layout Used: Bathurst 1983
Car Used: Porsche RSR 74
Applicable Settings: none
Report: Hole in collision mesh on the inside of Forest Elbow.

 

Can you make sure that your car detail setting is not set to LOW , as some models at lowest setting have mirrored textures on them (to save texture space I guess?) , in replay different detail settings are active than set in te performance menu.

 

Boy, keep cool

 

Track & Layout Used: ANY track , tested cars gt3 / super v8 / should affect any car with onboard settings
Applicable Settings: Multiplayer with enforced default settings
Report: When in a multiplayer game with enforced default setups , the in car menu disables all onboard controls like:
- anti lock brakes
- traction control
- brake bias
- front / rear roll bars
Steps to reproduce:
Start a multiplayer lobby with enforced default setups , add gt3 and super v8 classes , drive a practice session: mapped keys for all the onboard controls still work , but in car menu is completely greyed out and does not allow any change.

A separate in car menu issue, way in the past, not sure how to report this as older versions from a year+ ago is no longer around:
The fuel in the pitstop menu also changed color to RED if the amount of fuel would not be "enough" to finish the race (albeit a bit unprecise) .

 

I got car detail set to "HIGH". Have you tested the liveries ? Do you not have the graphical error ?

 

In the new update, this issue was not fixed yet

 

I can confirm this bug, even on ULTRA this is happening.
Barely noticeable with the stock livery of the mercedes truck, but visible degradation to the cabin and the "truck" sticker on the lower left gets mirrored.
Usually ULTRA does NO or minior detail switching for other cars (at least not that early), replay looks perfect in comparison. So something weird with LOD ranges for sure , switching way to soon to lowest mode.
Try LOW to only see mirrored textures during race (excluding only your own vehicle in external view)

 

Report: Sidewall of Formula Trainer and Formula Trainer Advance turns in the opposite direction than the tire when looking backwards.
Steps to reproduce: Slowly roll forwards / backwards with any Formula Trainer car looking back

 

Version: 1.4.6.1.2267.AVX
Track & Layout Used: Interlagos Kart One
Car Used: Kart GX390 Rental
Applicable Settings: Tested with Fanatec CSW 2.5 wheel, both with Default and Default+ FFB
Report: Soft stops when overturning the wheel (at more than 90 degrees with the Rental Kart) can no longer be felt, there is just a constant mild resistance.

Steps to reproduce:

1. Delete Documents\Automobilista 2 folder
2. Revert to branch previousbuild (version 1.4.5.2.2247.AVX)
3. Launch AMS2, calibrate wheel, calibrate pedals
4. Expected behavior: On track, overturn the wheel. At 90 degrees left or right, the soft stops are felt as a clear notch in the FFB, and the area outside of the soft stops has more resistance
5. Switch to branch releasecandidate or None (version 1.4.6.1.2267.AVX)
6. Launch AMS2, calibrate wheel, calibrate pedals
   
7. Bug: The soft stop notch as in Step #4 is no longer felt in the FFB
   1. Revert to branch previousbuild while keeping the upgraded Documents folder, then launching AMS2: Bug is still there!
   2. Staying on branch releasecandidate, deleting the Documents\Automobilista 2 folder, then launching AMS2: Bug is still there

AMS2 Beta build 2266 does not have this bug

 

Jup, take a look in that posts
https://forum.reizastudios.com/thre...officially-released.30136/page-21#post-226441
https://forum.reizastudios.com/thre...officially-released.30136/page-21#post-226481