T-LCM pedals not working

Do you have the pedals as separate?
Options.Controls.Control Scheme.Pedal Type <Separate>

 

allready assigned to another function should be no problem. Just say yes to assign it to this function

 

Where was this announced? Link?

 

Internet, Thrustmaster?

http://ts.thrustmaster.com/download...T_LCM/T-LCM_RJ12-pedal_set_mode_detection.pdf

 

All the document says is:

T2PA 2-pedal sets and T3PA and T3PA-PRO 3-pedal sets (Potentiometric type - low resolution)
T-LCM pedal set (magnetic and load cell type - high resolution)

As the T3PAs are less than 12 bit resolution (1028 - 10 bit?), they would always be lower resolution than the T-LCMs through the RJ12 (4096 - 12 bit). It doesn't specifically say anywhere that the RJ12 connection now gives 16 bit resolution. Or am I missing something?

 

The answer is on internet,
Example: New TM Base firmware update will allow 16-bit resolution for T-LCMs through the RJ12 cable : simracing

The link is to help you.

 

I don't think there is any official statement about it, but the only reason the mode would need to change via firmware is to allow this upgrade, as the connector already worked.

 

That post is not by anyone from Thrustmaster and that's not what the screenshot in the link says (see my previous post). Until someone from Thrustmaster announces this officially, it's just someone on Reddit jumping to conclusions - it may be correct but we have no way of knowing for certain.

 

I know the last post is old but for me it was the USB extension cable.

 

Dear All please check to PDF file. it happens coz, Firmware lost and you need to request "TLCMPEDALS_S32F373_v2_03.tmf" file from Thrustmaster support. if you share your e-mail also I can send you. I could not attach here coz file system.

I wrote you official guide about fixing the problem. Thrustmaster T-LCM Pedal Stuck happens coz, Firmware lost and you need to request "TLCMPEDALS_S32F373_v2_03.tmf" file from Thrustmaster support. if you share your e-mail also I can send you. I could not attach here coz file system.
or Please TLCMPEDALS_S32F373_v2_03.PDF file extention name change as "TLCMPEDALS_S32F373_v2_03.tmf" and use it.
with my best regards
My E-MAIL: Mertoglu.mk@gmail.com

Problem:
The gas pedal of your T-LCM is working randomly, sometimes gets stuck at 50%, 100%. Disconnect
and reconnect solves the issue but temporarily only.
An update may be necessary. The following steps will help you in this task. Be sure to respect them.
• In case you think you are not able to perform these operations, please contact Support.
• In case you do not notice any improvement at the end of the procedure, please contact
Support.
1- Preparation:
a) Disconnect all your THRUSTMASTER devices
b) In case you have already installed the drivers for a TH8 or a T-LCM in your PC, go to step
d)
c) Go to the webpage Thrustmaster - Technical support website to download
the driver package PACKAGE 2021_TH8RS_1 (for TH8). Install the package.
Restart your PC.
d) Drop the attached file TLCMPEDALS_S32F373_v2_03.tmf in the directory C:\ Program
Files\Guillemot\tmfwupdater\firmware
2- Connect the T-LCM in “boot mode”, for that:
Connect the USB cable to the back of the T-LCM. Press and hold the pairing button and
connect the USB cable to your computer.
The led should be off.
3- Perform the update
Open the TM Firmware Updater program
(available in the directory C:\Program Files\Guillemot\tmfwupdater\ as well)
The firmware version of your T-LCM appears in the “Device” window, and the new one (2.03) in
the “Firmware” window.
Click on “OK” to perform the update and follow instructions.
Click on “OK”. The firmware version in the “Device” window is now 2.03.
Close the program, your T-LCM is now up to date

 

Dear All please check to PDF file. it happens coz, Firmware lost and you need to request "TLCMPEDALS_S32F373_v2_03.tmf" file from Thrustmaster support. if you share your e-mail also I can send you. I could not attach here coz file system.

I wrote you official guide about fixing the problem. Thrustmaster T-LCM Pedal Stuck happens coz, Firmware lost and you need to request "TLCMPEDALS_S32F373_v2_03.tmf" file from Thrustmaster support. if you share your e-mail also I can send you. I could not attach here coz file system.
or Please TLCMPEDALS_S32F373_v2_03.PDF file extention name change as "TLCMPEDALS_S32F373_v2_03.tmf" and use it.
with my best regards
My E-MAIL: Mertoglu.mk@gmail.com

Problem:
The gas pedal of your T-LCM is working randomly, sometimes gets stuck at 50%, 100%. Disconnect
and reconnect solves the issue but temporarily only.
An update may be necessary. The following steps will help you in this task. Be sure to respect them.
• In case you think you are not able to perform these operations, please contact Support.
• In case you do not notice any improvement at the end of the procedure, please contact
Support.
1- Preparation:
a) Disconnect all your THRUSTMASTER devices
b) In case you have already installed the drivers for a TH8 or a T-LCM in your PC, go to step
d)
c) Go to the webpage Thrustmaster - Technical support website to download
the driver package PACKAGE 2021_TH8RS_1 (for TH8). Install the package.
Restart your PC.
d) Drop the attached file TLCMPEDALS_S32F373_v2_03.tmf in the directory C:\ Program
Files\Guillemot\tmfwupdater\firmware
2- Connect the T-LCM in “boot mode”, for that:
Connect the USB cable to the back of the T-LCM. Press and hold the pairing button and
connect the USB cable to your computer.
The led should be off.
3- Perform the update
Open the TM Firmware Updater program
(available in the directory C:\Program Files\Guillemot\tmfwupdater\ as well)
The firmware version of your T-LCM appears in the “Device” window, and the new one (2.03) in
the “Firmware” window.
Click on “OK” to perform the update and follow instructions.
Click on “OK”. The firmware version in the “Device” window is now 2.03.
Close the program, your T-LCM is now up to date

 

hey can you send me the firmware file?
My mail is privateer@outlook.com
Thanks !!!