Bug Reports - Automobilista 2 (Read the Opening Post)

Reply of Snetterton time trial. When replay finished the game crashes to bug splat.

 

Track & Layout Used: Velocitta
Car Used: Sprint race
Applicable Settings:
Report: Reparamos alguns problemas em Corridas online. Tem um bug que permite a troca de piloto mesmo quando nao ha outro piloto pra entrar no carro, ficando assim a IA andando na pista.
Steps to reproduce: Entrar em uma corrida, solicitar box, ativar troca de piloto.

 

Track & Layout Used: Bathurst
Car Used: Various (see below)
Applicable Settings: v1.0.0.3 in Time Trial mode
Report: All the Caterhams suffer from the FFB turning right after you gain control, which stays like this till you eventually crash. Other cars tried (Puma 052, Super V8, Formula V10 and Ultima Road) were all unaffected and drove nicely.
Steps to reproduce: Go into Time Trial mode and drive the Caterhams.

 

Track & Layout Used: Any track
Car Used: Any Copa Truck (Iveco, Man, Mercedes-Benz, and VW tested)
Applicable Settings: Night time
Report: Switching on headlights in copa truck does not switch on headlights, instead turns on glow for dash rpm meter.
Steps to reproduce: Go to any track at night and try toggling headlights. .

 

Track & Layout Used: -
Car Used: Ginetta G58 P1
Applicable Settings: -
Report: rear camber settings aren't symmetric / don't change symmetric
Rear right has also other values compared to rear left
Steps to reproduce: -

 

In addition to this, actually, sometimes the 'Symmetrical Setup check' is reversed.
For ex., when values don't change symmetrically while it is ticked, when you untick it, the values would change symmetrically. Sometimes, it works correctly, sometimes it doesn't.

Also, some values on the left and right columns cannot be changed until you highlight a value in the center column.

 

Track & Layout Used: Bathurst
Car Used: Any
Applicable Settings: v1.0.0.3 in Free Practice and Qualifying
Report: If time runs out and I am still on track doing laps I am announced the Practice or Qualifying is over but I cannot check any of the options leave the session or move to the next one. I have to use CTR+ALT+DEL to close the game.
If time runs out and I am still on track stopped and I do not finish at least one lap I am not announced the Practice or Qualifying is over and AI keep doing laps in an endless loop.
If I press ESC and go back to the pits I cannot check any of the options leave the session or move to the next one. I have to use CTR+ALT+DEL to close the game.
Steps to reproduce: Select "Single race" against AI do Practice and Qualifying

 

Track & Layout Used: Bathurst
Car Used: P4 Metalmoro Duratex MRX
Applicable Settings: v1.0.0.3 in any session
Report: In car "Setup menu"
-Symmetrical setup is checked
-Ride height values are not equal in the setup
/Uncheck Symmetrical setup
/Change values for Ride height until both values are equal
/Check Symetrical setup again
Front right tyre values gets reset to the initial value.
Steps to reproduce: Select "Single race" against AI go to car "Setup menu" change Ride height values

 

Track & Layout Used: Interlagos Modern
Car Used: Formula V10
Applicable Settings: Weather Variable
Report: Wet tires graphically displayed instead of dry tires, car behaves like on dry tires.
Steps to reproduce: During a variable weather quali session I came in as the rain started and I am using "adjust by weather". As the car went into the box the wet tires were shown on. Session finished without me driving again. I loaded the race setup (always with tires on "adjust by weather") and once at race grid tires were still showing as wet. As I came in first lap to have them swapped they felt like dry tires while driving. Once in the pit when the tires came off all of a sudden they were graphically shown as dry. The new ones came on still showing as wet. I finished the race with lap times as on the dry tires, so the problem is only graphical

 

Track & Layout Used: Imola
Car Used: Mitsubishi Lancer RS
Applicable Settings: TT
Report: In setup it is not possible to change tire pressure or settings for the front differential. Also rear brakes don't seem to work.
Steps to reproduce:

 

Track & Layout Used: Any
Car Used: Any
Applicable Settings: MP
Report: Looks like MP lobby realism settings changes your personal default settings.
Steps to reproduce:Setup personal realism setting to full / max. Go into a MP lobby with realism settings set to off. When you exit and return to main menu your personal settings will now be changed to mirror MP lobby settings

 

Track & Layout Used: Any track
Car Used: F-Ultimate
Applicable Settings: Any settings
Report: FFB bugs(The steering is forced to turn to the right.)
Steps to reproduce: Using a controller with FFB and going out to tracks with F_Ultimate

 

This issue we had in EA but was fixed. Are you sure you have the lastest version of AMS? (1.0.0.3)
What FFB setting do you use?

 

Track & Layout Used: Any (but tried in Bathurst, Adelaide).
Car Used: Ginetta GT4
Applicable Settings: Any
Report: Accelerator does not reach 100% (like 95% only), regardless of track. Other cars tried (Stock Car, Super V8) reach 100%
Steps to reproduce: I'm using Simhub pedal inputs to see this. Green bar doesn't reach the top, whereas it does with the other cars tested. (Also tried in both Beta and Release version and issue appears in both).

 

What kind of engine map do you use?
In setup, you can choose 0.9, 0.95 and 1.0 (for most cars).
I know, in telemetry software (RST) this will impact the max. throttle position value which is 90%, 95% or 100%.
How it will have an effect on in-game telemetry-tool, I don't know at the moment.

 

Houston, we have a problem

Track & Layout Used: Cascavel
Car Used: Hot Cars / Pas HC
Applicable Settings: TT
Report: Got off track right before T3, drove up the hill towards the Stands, went through the Stands and then in to the Sun
Steps to reproduce: See above

 

What's up with your windshild? Is it splittered? New feature?

 

Thanks for the info, will check it again tom. Isn't it set by default to 100%?
UPDATE: Indeed it was at 90%, most likely got changed when my wheel was not centered when I viewed setup, even with wheel rotation set to 0 in controls.

REQUEST: REIZA, can we pls remove the Menu Editing by Wheel rotation.

 

As I think, it's not always on 1.0. Sometimes it had other settings but I can't say if it's dependig on car, track, or something else. Sometimes I have the feeling that setup settings are kept in memory and will be reused if you switch the car (within this car's limitiations and opportunities). So if you switch the car or track, not always a default setup will be loaded at the first time. Maybe this should be reported as a bug but I always forget or I'm not really sure...

 

No, that are the outlines from the environment that should be below the car